Wieland ricos FLEX User Manual Download Page 20 | Manualshive

Page: 20 / 54

background image

Basics and Assembly

20

Wieland Electric GmbH | BA000941 | 01/2014 (Rev. A)

Clack

1

2

3

4

1

Shield bus carrier

2

Shield bus (10 mm x 3 mm)

3

Shield clamp

4

Cable shield

3.6

Trouble-shooting - LED

Each module has the LEDs RUN and MF on its front side. Errors or incorrect modules may
be located by means of these LEDs.

In the following illustrations flashing LEDs are marked by

☼

.

Behavior:

After PowerON the RUN LED of each module is off and the MF LED of
each module is sporadically on.

Reason:

The maximum current for the electronic power supply is exceeded.

Remedy:

As soon as the sum current of the electronic power supply is exceeded,
always place the power module PW 24 V / 5 V (order number:
83.036.0040.0).

More concerning this may be found above at

"Wiring".

Behavior:

After PowerON the MF-LED of one module respectively more modules
flashes. The RUN-LED remains off.

Reason:

At this position a module is placed, which does not correspond to the
configured module.

General

Sum current of

the electronic
power supply
exceeded

Error in

configuration

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

«
...
18
19
20
21
22
...
»

Summary of Contents for ricos FLEX























































Reviews:

No comments

Related manuals for ricos FLEX

Brand: Nelsen Corporation Pages: 16

Brand: National Instruments Pages: 34

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 2

ECL Comfort 110

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands