Whirlpool Vessi Use And Care Manual Download Page 12

Page: 12 / 40

| SETTING UP YOUR VESSI™ FERMENTOR & DISPENSER

UNPACKING

Cut straps, open top flaps, and

remove foam blocks and corner

posts� Lift the carton off� Dispose

of/recycle all packaging materials�

Using a

wrench, remove the

4 shipping brackets�

WARNING

Excessive Weight Hazard

Use two or more people to move

and install VESSI™ Fermentor

& Dispenser.
Failure to do so can result in

back or other injury.

Using 2 or more people, lift the

fermentor

from the pallet�

The Vessi™ Fermentor &

Dispenser has 2 swivel casters in

the rear and 2 non-swivel locking

casters in the front� Push the

fermentor from the front, keeping

the swivel casters forward for

proper steering�
Set the fermentor in place and,

if desired, lock the 2 front casters�

Remove accessory bag from inside

the vessel and from the base shelf�

Unpack and dispose of/recycle

all packaging materials�

INSTALLING THE CO

TANK

WARNING

Asphyxiation Hazard

Do not use a CO2 tank larger

than 5 lbs.
Doing so can result in death or

serious injury.

A 5-lb food grade CO

tank (to be

installed inside the fermentor) is needed�

One may be rented from a gas supply

company�

IMPORTANT:

Reference all warnings

provided with the CO

tank�

SETTING UP YOUR VESSI™ FERMENTOR

& DISPENSER

Summary of Contents for Vessi









































Search results

Summary of Contents for Vessi

Reviews:

Related manuals for Vessi

Brands by name

Popular brands

Whirlpool Vessi, Use And Care Manual

Search results

Summary of Contents for Vessi

Reviews:

Related manuals for Vessi

Brands by name

Popular brands