5-9
FOR SERVICE TECHNICIANS ONLY
MANUAL TEST MODE —
See page to access Manual Test Mode
Pressing the START button will activate/deactivate each output. When the output is activated, the
corresponding Status LED’s will
flash.
NOTE:
Lid must be closed and locked to perform SPIN tests.
OUTPUT
DISPLAY
Output Details
NOTE:
Outputs will time-out after 5 minutes.
SENSING
SOAK
W
ASH
RINSE
SPIN
DONE
LID LOCK
If Available
LID LOCK
00
COLD VALVE
On
01
HOT VALVE
On
02
RESERVED FOR FUTURE DEVELOPMENT
On On
03
RESERVED FOR FUTURE DEVELOPMENT
On
04
FABRIC SOFTENER DISPENSER
On
On
05
OXI DISPENSER
On On
06
DRAIN
On On On
07
RESERVED FOR FUTURE DEVELOPMENT
On
08
LOW SPIN
On
On
On
09
HIGH SPIN
On
On
On
10
GENTLE AGITATION
On
On On
1 1
HEAVY AGITATION
On On
12
Allow up to 15 seconds for shifter to reposition.
Shifts from idle motor to heavy CW/CCW agitation.
IMPORTANT:
To activate Heavy Agitation, RPM must read “0” and lid must be closed with lid lock enabled. If lid is not closed,
washer will beep and LED’s will flash.
• If motor does not agitate, go to
TEST #3a & 3b: Drive System (Shifter & Motor).
STATUS LEDs
If selected, washer will beep and LED’s will flash.
Allow up to 15 seconds for shifter to reposition.
Spins basket from 0 to 500 RPM.
IMPORTANT:
Water in tub must be drained before test.
IMPORTANT:
To activate Low Spin, RPM must read “0” and lid must be
closed with lid lock enabled. If lid is not closed, washer will beep and LED’s will flash.
• If motor does not spin, go to
TEST #3a & 3b.
Allow up to 15 seconds for shifter to reposition.
Spins basket from 0 to maximum RPM.
To activate High Spin,
IMPORTANT:
Water in tub must be drained before test.
IMPORTANT:
To activate High Spin, RPM must read “0” and lid must be
closed with lid lock enabled. If lid is not closed, washer will beep and LED’s will flash.
• If motor does not spin, go to
TEST #3a & 3b.
Allow up to 15 seconds for shifter to reposition.
Shifts from idle motor to gentle CW/CCW agitation.
IMPORTANT:
To activate Gentle Agitation, RPM must read “0” and lid must be closed with lid lock enabled. If lid is not closed,
washer will beep and LED’s will flash.
• If motor does not agitate, go to
TEST #3a & 3b: Drive System (Shifter & Motor).
If selected, washer will beep and LED’s will flash.
Turns ON and turns OFF the fabric softener valve. (May not be available on all models or brands.)
• If valve does not turn on, go to
TEST #2.
Turns ON and turns OFF the Oxi dispenser valve. (May not be available on all models or brands.)
• If valve does not turn on, go to
TEST #2.
Turns ON and turns OFF the drain pump.
• If pump does not turn on, go to
TEST #7.
Lock and unlock the lid.
NOTES:
When lock is enabled, the “Lid Lock” LED will turn ON. Will only lock when lid is closed. Will only
unlock when basket RPM is 0. If lid is not closed, washer will beep and LED’s will flash.
• If lid does not lock or unlock, go to
TEST #8.
Turns ON and turns OFF cold water valve.
• If valve does not turn on, go to
TEST #2.
Turns ON and turns OFF hot water valve.
• If valve does not turn on, go to
TEST #2.
If selected, washer will beep and LED’s will flash.
On
On
Summary of Contents for Cabrio WTW5700XW
Page 58: ...4 22 NOTES ...
Page 84: ......
