5-6
FOR SERVICE TECHNICIANS ONLY
FAULT/ERROR CODES (continued) —
See page to access Fault Code Display Mode
* If the Sensing LED is ON, the fault code number is represented; if OFF, the error code number is represented.
DESCRIPTION
SENSING*
W
ASH
RINSE
SPI
N
DONE
SENSING*
W
ASH
RINSE
SPI
N
DONE
OVER SUDS CONDITION DETECTED
On
f0
On
e2
STUCK KEY
On
On
f2
On
e1
MISMATCH OF MAIN CONTROL & UI
On
On
f2
On On
e3
PRESSURE SENSOR FAULT
On
On On
f3
On
e1
INLET WATER TEMPERATURE FAULT
On
On On
f3
On
e2
LID SWITCH FAULT
On
On
On
f5
On
e1
ERROR NUMBER
FAULT NUMBER
Fault is displayed if Lid Switch has not been detected after multiple wash cycles.
• User presses ST
AR
T
with lid open.
• The main control cannot detect the lid switch opening and closing properly
.
• See TEST
#8: Lid Lock.
Fault is displayed when the Inlet
Thermistor is detected to be open or shorted.
• See TEST
#5:
T
emperature
Thermistor
.
Fault is displayed when the Main Control detects an out of range pressure signal.
• Check pressure hose connection from tub to main control. Is hose pinched, kinked, plugged, or leaking air
?
• See TEST
#6: Water Level.
The User Interface identification does not match the expected v
alue in the Main Control Board.
• Fault occurs during Diagnostic T
e
st Mode if a mismatch of main control and UI is identified.
• See TEST
#4: Consoles and Indicators.
Explanation & Recommended Procedur
e
One or more keys on the User Interface were actuated for 15 con
secutive seconds.
• Fault occurs during Diagnostic T
est Mode if a stuck key is detected.
• See TEST
#4: Consoles and Indicators.
Status LEDs
Status LEDs
DISPLA
Y
Fault is displayed when Suds prevent the basket from spinning up to speed or the pressure sensor detects rising
suds level.
The main control will flush water in attempt to clear Suds. If
the water flush is unable to correct the
problem, this may indicate:
• Not using HE detergent.
• Excessive detergent usage.
• Check pressure hose connection from tub to main control. Is hose pinched, kinked, plugged, or leaking air
?
• Mechanical friction on drive mechanism or basket. (Clothing b
etween basket and tub.)
DISPLA
Y
HIGH WATER TEMPERATURE – RINSE CYCLE
On
f0
On
e4
OFF BALANCE LOAD DETECTED
On
f0
e5
MAIN CONTROL FAULT
On
On
f1
On
e1
MOTOR CONTROL FAULT
On
On
f1
On
e2
Indicates a fault of the motor control section of the main control.
• See TEST
#3b: Drive System.
Indicates a main control fault.
• See TEST #1: M
ain Control.
Fault is displayed when an off balance condition is detected.
• Check for weak suspension. Basket should not bounce up and do
wn more than once when pushed.
• Clothing should be distributed evenly when loading.
Fault is displayed when washer detects water temperature 105° or higher during rinse cycle.
• Hot water getting in. Make sure inlet hoses are connected cor
rectly.
• See TEST #5: Temperature Thermistor.
• If hoses are installed properly, temperature thermistor may be stuck in low resistance range.
On
On
LID LOCK FAULT
On
On
On
f5
On
e2
Fault is displayed if Lid Lock has not moved into locked position or motor cannot be powered.
• Lid is not closed completely due to interference.
• Check for lock interference with lock striker.
•
Wa
sh media buildup (detergent, lint, etc.) is preventing the lock mechanism from sliding.
• Main control detects open lid switch when attempting to lock.
• Main control cannot determine if lid lock is in a locked stat
e.
• See TEST
#8: Lid Lock.
F0
F0
F0
F1
F1
F2
F2
F3
F3
F5
F5
E2
E4
E5
E1
E1
E1
E1
E2
E2
E3
E2
Summary of Contents for Cabrio WTW5700XW
Page 58: ...4 22 NOTES ...
Page 84: ......
