Whirlpool AER5522VAS0, Manual

Page: 27 / 70

18 1-
Reviewed by Perkins, Amber F. | Released
MGR8670WB0
MGR8670WB1
MGR8670WQ0
MGR8670WQ1
MGR8670WS0
MGR8670WS1
MGR8670WW0
MGR8670WW1
LCC190 Control, Self Clean, Gas
LCC Control, Self Clean, Gas
Previous Offset shown, or U-00 is displayed.
Adjusts temperature in 10
⁰ F (5⁰ C) increments
between -30⁰F and +30⁰F.
Display
"tESt" (You are in the test mode)
###⁰F or ⁰C (Oven Sensor Temperature)
-30⁰F to +30⁰F (Oven Offset Temperature)
### (Control Software Version)
### (Control Memory Checksum)
"CLr" (Good Control)
F# *(Error Code - See Tech Sheet for Repair) ##
(Hours of operation at error code)
#### (Total hours of oven operation)
"00" (Door Open) or "01" (Door Closed)
B, D, E, F, M, T, U, V, AD, AE, AF, AN, AO, AP, AU
Diagnostic Mode
Press CANCEL/CANCEL/START.
Action
"+" again
"+" again will display 1 of the 3
"+" again
"+" again
"+" again
When checking for fault codes and "GOOd" is displayed, do not replace the control.
*Press "START" to clear all fault codes.
Temperature Adjustment
Press TEMP/TIME or
TEMP/HOUR "+" or "-".
Press BAKE for 5 seconds.
Press START.
Press the TEMP/TIME or
TEMP/HOUR "+" key.
Press "+" again
Bake and Broil Temperatures are offset
automatically to the same degree.
If START is not pressed within 1 minute, adjustment
is ignored.
Models:
Press TEMP/TIME “+” or “-”.
Press TEMP/TIME “+” key.
(Hours of operation at error code)
“GOOd”
##
4
FOR SERVICE TECHNICIAN’S USE ONLY
Wiring Diagram
NOTE: Schematic shows door latch switch in the COOK position with oven door open and elements off.
Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
L1
N
BK
BK
Con 2-4
Oven Control LCC190
CON 3-3
CON 3-1
CON 3-4
CON 3-9
CON 3-10
CON 1-5
Oven Light (K2)
Power Supply
CON 1-1
CON 1-4
Latch Motor (K4)
Bake (K7) CON 2-7
Broil (K6)
CON 2-1
Y
BU
GY
V
V
BK
W
BR
R/W
BU/W
GY
GY
Door Position Switch
Door Latch Switch
Oven Temp Sensor
W
W
W
W
W
Oven Light Assy 40W
Latch Motor 4W
R
Y
Bake Igniter Bake Valve
Broil Igniter
Broil Valve
BU R
W
T
L1 N G
Burner
Burner
Burner
Burner
Burner
Spark Module
GND
T
BK
BK
Surface Burner Ignition Switch
LEGEND
Component
Terminals
Connection
(Splice)
No
Connection
On Some
Models
In Line
Connection
CON1-2 = Connector 1
CON1 Position 2
Multiple
Functions / Circuitry
Enclosed Within
*Press “DELAY START” to clear all fault codes