Whirlpool AER5522VAS0, Manual

Page: 39 / 70

2 2-
GFE461LVB0
GFE461LVQ0
GFE461LVS0
GFE461LVT0
YGFE461LVB0
YGFE461LVQ0
YGFE461LVS0
Reviewed by Staples, Debra L. | Released
MRC Control, True Convection, Steam Clean, Electric
MRC Convection, Electric
Models:
Models:
MRC Control, True Convection, Warming Drawer, Steam Clean, Electric
Reviewed by Staples, Debra L. | Released
GFE471LVB0
GFE471LVQ0
GFE471LVS0
YGFE471LVB0
YGFE471LVQ0
YGFE471LVS0
Previous Offset shown, or U-00 is displayed.
Adjusts temperature in 5
⁰F (3⁰C) increments
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Bake and Broil Temperatures are offset
automatically to the same degree.
If START is not pressed within 1 minute,
adjustment is ignored.
Display
"TEST ON" ##⁰F "UO" (In the test mode)
"USAGE" (Displays hours of Operation)
"ENG MODE" (Manufacturing Information)
"TEST MODE" (Manual check of Control relays)
"VERSION" (Manufacturing Information)
"DISPLAY" (Checks all LEDs in Display)
"CONTROL RESET" (Resets Control settings)
"FAULTS" *(Displays all Fault Codes)
"AUTO TEST" (Performs a complete check of
the OVEN, automatically)
When checking for fault codes and "NO FAULTS" is displayed, do not change the control.
"+" again
"+" again
Diagnostic Mode
1. Press CANCEL/CANCEL/START
2. Press the TEMP/TIME "+" key
Action
Press "+" again
"+" again
"+" again
"+" again
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy
to use and when the test is complete, test results will be provided. Whenever servicing the
oven, this is the test to run.
When in the Diagnostic mode, instructions will be provided by the control to help you
through each of the programs. Press Cancel to exit the test at any time.
*Press Start Time to clear all fault codes
Temperature Adjustment
2. Press TEMP/TIME "+" or "-".
1. Press "BAKE" for 5 seconds.
3. Press START.
"+" again
Previous Offset shown, or U-00 is displayed.
Adjusts temperature in 5
⁰F (3⁰C) increments
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Bake and Broil Temperatures are offset
automatically to the same degree.
If START is not pressed within 1 minute,
adjustment is ignored.
Display
"TEST ON" ##⁰F "UO" (In the test mode)
"USAGE" (Displays hours of Operation)
"ENG MODE" (Manufacturing Information)
"TEST MODE" (Manual check of Control relays)
"VERSION" (Manufacturing Information)
"DISPLAY" (Checks all LEDs in Display)
"CONTROL RESET" (Resets Control settings)
"FAULTS" *(Displays all Fault Codes)
"AUTO TEST" (Performs a complete check of
the OVEN, automatically)
When checking for fault codes and "NO FAULTS" is displayed, do not change the control.
"+" again
"+" again
Diagnostic Mode
1. Press CANCEL/CANCEL/START
2. Press the TEMP/TIME "+" key
Action
Press "+" again
"+" again
"+" again
"+" again
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy
to use and when the test is complete, test results will be provided. Whenever servicing the
oven, this is the test to run.
When in the Diagnostic mode, instructions will be provided by the control to help you
through each of the programs. Press Cancel to exit the test at any time.
*Press Start Time to clear all fault codes
Temperature Adjustment
2. Press TEMP/TIME "+" or "-".
1. Press "BAKE" for 5 seconds.
3. Press START.
"+" again
*Press “START TIME” to clear all fault codes