Whirlpool AER5522VAS0, Manual

Page: 33 / 70

24 1-
MGR7775WB0
MGR7775WB1
MGR7775WS0
MGR7775WS1
MGR7775WW0
MGR7775WW1
LCC190 Control, Self Clean, Convection, Gas
LCC Self Clean, Convection, Gas
Released
Models:
Models:
LCC190 Control, Self-Clean, Convection, Gas
AGR6011VDB0
AGR6011VDB1
AGR6011VDS0
AGR6011VDS1
AGR6011VDW0
AGR6011VDW1
Reviewed by Staples, Debra L. | Released
Previous Offset shown, or U-00 is displayed.
Adjusts temperature in 10
⁰ F (5⁰ C) increments
between -30⁰F and +30⁰F.
Display
"tESt" (You are in the test mode)
###⁰F or ⁰C (Oven Sensor Temperature)
-30⁰F to +30⁰F (Oven Offset Temperature)
### (Control Software Version)
### (Control Memory Checksum)
"CLr" (Good Control)
F# *(Error Code - See Tech Sheet for Repair) ##
(Hours of operation at error code)
#### (Total hours of oven operation)
"00" (Door Open) or "01" (Door Closed)
B, D, E, F, M, T, U, V, AD, AE, AF, AN, AO, AP, AU
Diagnostic Mode
Press CANCEL/CANCEL/START.
Action
"+" again
"+" again will display 1 of the 3
"+" again
"+" again
"+" again
When checking for fault codes and "GOOd" is displayed, do not replace the control.
*Press "START" to clear all fault codes.
Temperature Adjustment
Press TEMP/TIME or
TEMP/HOUR "+" or "-".
Press BAKE for 5 seconds.
Press START.
Press the TEMP/TIME or
TEMP/HOUR "+" key.
Press "+" again
Bake and Broil Temperatures are offset
automatically to the same degree.
If START is not pressed within 1 minute, adjustment
is ignored.
Previous Offset shown, or U-00 is displayed.
Adjusts temperature in 10
⁰ F (5⁰ C) increments
between -30⁰F and +30⁰F.
Display
"tESt" (You are in the test mode)
###⁰F or ⁰C (Oven Sensor Temperature)
-30⁰F to +30⁰F (Oven Offset Temperature)
### (Control Software Version)
### (Control Memory Checksum)
"CLr" (Good Control)
F# *(Error Code - See Tech Sheet for Repair) ##
(Hours of operation at error code)
#### (Total hours of oven operation)
"00" (Door Open) or "01" (Door Closed)
B, D, E, F, M, T, U, V, AD, AE, AF, AN, AO, AP, AU
Diagnostic Mode
Press CANCEL/CANCEL/START.
Action
"+" again
"+" again will display 1 of the 3
"+" again
"+" again
"+" again
When checking for fault codes and "GOOd" is displayed, do not replace the control.
*Press "START" to clear all fault codes.
Temperature Adjustment
Press TEMP/TIME or
TEMP/HOUR "+" or "-".
Press BAKE for 5 seconds.
Press START.
Press the TEMP/TIME or
TEMP/HOUR "+" key.
Press "+" again
Bake and Broil Temperatures are offset
automatically to the same degree.
If START is not pressed within 1 minute, adjustment
is ignored.
Press TEMP/TIME “+” key.
Press TEMP/TIME “+” or “-”.
(Hours of operation at error code)
*(Error Code - See Tech Sheet for Repair)
“GOOd”
##
*Press “START TIME” or “DELAY START” to clear all fault codes