WebGate eDVR MD800M Installation Manual Download

Page: 57 / 67

When using RAID

The following description is when MD800M has internal primary disk and 1 set of IEEE1394 RAID.

Even though several HDDs are connected to RAID, MD800M will recognize them as only one HDD.

For connection and setup of RAID, please refer to the manual of related device.

(1)

When external HDD RAID is connected to eSATA port, “Disk Manager” runs automatically. If not,

run it manually in “Menu

Utility

Disk Manager”.

(2)

Select a second HDD of [F] Ext and configure a size of alarm partition. Press the “Apply” button

after selecting action as “Add”. Then [F] is changed to [R].

<ote>

If connecting the device that is used in MD800M, type will be indicated as [V].

(3)

Press the [EXIT] button to shut down “Disk Manager”.

Summary of Contents for eDVR MD800M




































































Search results

Summary of Contents for eDVR MD800M

Reviews:

Related manuals for eDVR MD800M

Brands by name

Popular brands

WebGate eDVR MD800M, Installation Manual

Search results

Summary of Contents for eDVR MD800M

Reviews:

Related manuals for eDVR MD800M

Brands by name

Popular brands