Webasto HOLLANDIA 700 - 20 Series Service Manual Download Page 29

Page: 29 / 30

3. REPAIRS

3.10 Seal adjustment HOLLANDIA 700 - 20 series

The proper positioning of the steel panel should locate the seal firmly in touch with either the EPDM trim ring

or flanged metal circumference of the sunroof opening. If the panel fits properly yet there remains a gap

between seal and trim ring it can be corrected as follows:

Readjust panel according to instructions in the installation manual chapter 5.3.

With a grease pencil mark the boundaries of insufficient contact on the panel.

3. Remove

panel.

In the areas marked a spacer will be inserted between panel retaining channel and rubber seal.

(Figure 3.12.1)

Figure 3.12.1

Remount panel and adjust according to the installation manual chapter 5.3.

Summary of Contents for HOLLANDIA 700 - 20 Series































Search results

Summary of Contents for HOLLANDIA 700 - 20 Series

Reviews:

Related manuals for HOLLANDIA 700 - 20 Series

Brands by name

Popular brands

Webasto HOLLANDIA 700 - 20 Series, Service Manual

Search results

Summary of Contents for HOLLANDIA 700 - 20 Series

Reviews:

Related manuals for HOLLANDIA 700 - 20 Series

Brands by name

Popular brands