Webasto HOLLANDIA 700 - 20 Series Service Manual Download Page 30

Page: 30 / 30

3. REPAIRS

3.11 Seal adjustment HOLLANDIA 700 - 40 series

The proper positioning of the panel should result in the seal firmly contacting either the EPDM trim ring or

flanged metal of the sunroof opening. If the panel fits properly but gaps remain between seal and trim ring it

can be corrected as follows:

Adjust panel (1) properly against the rear of the trim profile (36) (according to instructions in the

installation manual chapter 5.3).

With a grease pencil mark the boundaries of insufficient contact on the panel (at the front).

3. Remove

panel.

In the areas marked, a spacer will be inserted inside the rubber seal. (Figure 3.12.1). Use a vinyl

tube with outer diameter of 3 mm (0.12 in) for spacer material.

Glue the spacer material to the seal with super glue.

Figure 3.12.1

Remount panel and adjust according to the installation manual chapter 5.3.

Summary of Contents for HOLLANDIA 700 - 20 Series































Search results

Summary of Contents for HOLLANDIA 700 - 20 Series

Reviews:

Related manuals for HOLLANDIA 700 - 20 Series

Brands by name

Popular brands

Webasto HOLLANDIA 700 - 20 Series, Service Manual

Search results

Summary of Contents for HOLLANDIA 700 - 20 Series

Reviews:

Related manuals for HOLLANDIA 700 - 20 Series

Brands by name

Popular brands