Webasto HOLLANDIA 700 - 20 Series Service Manual Download Page 8

Page: 8 / 30

1. FAILURES

1.3

REPAIR ADVICE FOR RATTLING NOISE

PROBLEM POSSIBLE

CAUSE

SOLUTION

Drain channel rattles.

Check if insulation tape is

applied between drain channel

and mechanism.

Add insulation tape.

Steel panel ventilation tray

rattling.

1. Curvature of front ventilation

tray incorrect.

2. Insufficient contact between

rail and ventilation tray tumbling

mechanism.

3. Wires insufficiently secured.

1. Manual adjust the curvature of

the ventilation tray.

2. Correct rear side ventilation

tray to improve rail contact.

3. Secure wires.

Rattle in motor area.

Loose screws on motor cover

plate.

Tighten motor cover plate

screws.

1.4.

REPAIR ADVICE FOR WIND NOISE

PROBLEM POSSIBLE

CAUSE

SOLUTION

Excessive wind noise when the

panel is in the closed position.

1. Panel seal not tight to trim

ring.

2. Blocking catch broken

1. Re-adjust the panel. (see

installation manual 5.3)

2. Replace blocking catch,

see 3.9

Whistling sound when panel is

placed in the tilt position.

Vinyl headliner material wrapped

around sunshade too thin,

creating large wind channel

between mechanism rail and

side of sunshade.

Place insulating tape along

either outboard edge of

sunshade to close channel.

See installation manual 4.1.6

Steel panel vented emitting

whistling sound.

Vinyl headliner material wrapped

around trim tray too thin,

creating large wind channel

between mechanism rail and

side of trim-tray

Place insulating tape along

either outboard edge of trim tray

to close channel. See installation

manual 4.1.6

Summary of Contents for HOLLANDIA 700 - 20 Series































Search results

Summary of Contents for HOLLANDIA 700 - 20 Series

Reviews:

Related manuals for HOLLANDIA 700 - 20 Series

Brands by name

Popular brands

Webasto HOLLANDIA 700 - 20 Series, Service Manual

Search results

Summary of Contents for HOLLANDIA 700 - 20 Series

Reviews:

Related manuals for HOLLANDIA 700 - 20 Series

Brands by name

Popular brands