Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 9

Page: 9 / 53

95-03009

WAUKESHA CENTRIFUGAL 200 Series PUMPS

SPECIFICATIONS

2045

2065LV

2065
2065HV
2085LV
2085

2105

CAPACITIES 200 SERIES

SANITARY

MODE

INDUSTRIAL INLET OUTLET MAXIMUM MAXIMUM

MODEL SIZE

SIZE IMPELLER SIZE CAPACITY

inch (mm) inch (mm) inch (mm) GPM (M3/HR)

U2045

1.5 (40)

4.5 (115)

TO 190 GPM (43)

2.0 (50)

1.5 (40)

4.5 (115)

TO 190 GPM (43)

U2065LV

1.5 (40)

6.5 (165)

TO 200 GPM (45)

2.0 (50)

1.5 (40)

6.5 (165)

TO 200 GPM (45)

2.5 (65)

1.5 (40)

6.5 (165)

TO 200 GPM (45)

U2065

2.5 (65)

2.0 (50)

6.5 (165)

TO 400 GPM (91)

U2065HV

3.0 (75)

2.0 (50)

6.5 (165)

TO 500 GPM (114)

U2085LV

2.0 (50)

1.5 (40)

8.5 (215)

TO 143 GPM (33)

U2085

3.0 (75)

2.5 (65)

8.5 (215)

TO 840 GPM (191)

4.0 (100)

2.5 (65)

8.5 (215)

TO 840 GPM (191)

U2105

4.0 (100)

10.5 (265)

TO 1400 GPM (318)

6.0 (150)

4.0 (100)

10.5 (265)

TO 1400 GPM (318)

PERFORMANCE CHARACTERISTICS

Nominal Capacity:

To 1150 U.S. GPM
(260 Cubic Meters/Hr.)

Viscosity:

To 1500 CPS

Differential Pressure:

To 340 Feet (100 Meters)

Temperature:

To 450°F (230°C)

Nominal Speeds:

1450 or 2900 RPM - 50HZ;
1750 or 3500 RPM - 60HZ.

OUALlTY CONTROL:

Each pump undergoes a performance test for design flow
rate and design pressure prior to shipment.

AUTHORIZATION:

3A/USDA

(SANITARY

MODELS)

STANDARD CONSTRUCTION:

Casing:

316L Stainless Steel

Port Connections:

S-Line

Backplate:

316L Stainless Steel

Impeller W/Integral Shaft

: 316L Stainless Steel

Impeller Retainer:

316L Stainless Steel

Shaft Seal:

Single Mechanical, external
balanced (Type 1)

Rotary Seal Material:

Carbon

Stationary Seal:

Siliconized Graphite

Elastomers:

FDA approved Viton

Finish:

All product contact surfaces provided with a

sanitary polish (150 Grit)

(Industrials, unpolished)

Motor

Adapter Bracket: Cast Iron Paint: Two-part epoxy,
TNEMEC 104, Sky-Blue #104-BB-42 - on motor bracket
and motor (if ordered)

Mounting:

Close coupled for JM shafted
motors

OPTIONS:

Ports:

Bevel Seat
Female I-Line
Male I-Line
Q-Line
Butt-weld
Female or Male N.P.T
150 Lb. Flange, DIN or SMS

Seal Type:

• Water Cascade (Type 1C)
• Double Mechanical w/flush (Type 4 Shaft Seal)
• WFI - Special Type 4 Shaft Seal for Water for Injection
applications
• Aseptic Shaft Seal - barrier flush design
• Commercially available seals (CALL DISTRIBUTOR)

Rotary Seal Material:

Purebide, Silicone Carbide, Tungsten Carbide

Stationary Seal:

Silicone Carbide, Tungsten Carbide

Elastomers:

*EPDM, *Silicone, *Teflon Encapsulated or Kalrez (*FDA
approved)

Finishes/Product Contact Surfaces:

25RA, 20RA, Electropolish, (Unpolished -Industrial)

Casing Drain

Leg Kit SEE PAGE 34

Base Mounting to

: Footless C-face motors; Footed C-face

motors; T-Frame motors.

(NOTE: With or without bases, couplings or coupling
covers.)

Pedestal Mounted:

Three types on stands (See Page 37)

Motors:

NEMA JM (standard) totally enclosed fan cooled
(TEFC) for close-coupled pumps.
1750 or 3500 RPM Single phase 115/230 volt and
3 phase 230/460 volt.

Optional Enclosures:
Washdown, Explosion proof,
Severe Duty/Chemical Duty

Summary of Contents for 200 series






















































Search results

Summary of Contents for 200 series

Reviews:

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 9 / 53

Search results

Summary of Contents for 200 series

Reviews: