manualshive.com logo in svg

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 4 / 53

Share
Download
Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 4

3

95-03009

Read and understand this manual prior to
installing, operating or maintaining this pump.

WARNING

TO AVOID  SERIOUS INJURY, DO NOT

INSTALL OR SERVICE PUMP UNLESS

ALL POWER  IS OFF AND LOCKED OUT.

WARNING

TO AVOID POSSIBLE SERIOUS INJURY,

SHUT OFF AND DRAIN PRODUCT FROM

PUMP PRIOR TO DISCONNECTING PIPING.

WARNING

To avoid electrocution,  ALL electrical should

be done by a registered Electrician, following

Industry Safety Standards.

All power must be OFF and LOCKED OUT

during installation.

Do Not operate pump

without CASING

clamped securely in place.

WARNING

33-61

33-62

4-18-97

SAFETY

Operators and maintenance personnel must follow safety measures. Failure to observe the
instructions in this manual could result in severe personal injury or machine damage.

• Throughout this manual the words Warning, Caution, and Note are used to indicate

procedures or situations which require special operator attention.

WARNING

Identifies a serious hazard and how to avoid it. Failure to avoid this
hazard can cause serious personal injury.

CAUTION

Identifies a potential hazard and how to avoid it. Failure to avoid this
hazard could result in personal injury and/or machine damage.

NOTE

Important information pertaining directly to the subject. (Information
to be aware of when completing the task.)

Summary of Contents for 200 series






















































Reviews:

No comments