manualshive.com logo in svg

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 15 / 53

Share
Download
Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 15

14

95-03009

ELECTRICAL CONNECTIONS

MOTOR

1. Read motor manufacturer's instructions
before making installation.
2. Read nameplate to be certain that motor is
compatible with electrical supply and that all
wiring, switches, starters, and overload
protection are correctly sized.
3, Following electrical installation, check
pump rotation

.  Facing pump, the correct

rotation is counterclockwise. 

(Figure 15)

Do this procedure after disassembly for final
cleaning and prior to 

FINAL PUMP CHECK.

INSTALLATION

WARNING

To avoid electrocution,  ALL electrical

installation should be done by a registered

Electrician, following Industry Safety

Standards.

All power must be OFF and LOCKED OUT

during installation.

CLEAN PUMP AND PIPING

Disassemble pump and clean all product contact
parts and seal parts prior to first operation.
Follow instructions 

Disassembly for Cleaning

and Repair 

in the 

MAINTENANCE

 section of

this manual. Flush and clean all system piping
and process equipment separately. This will
eliminate any foreign material which could have
accumulated during installation. Plant workers
will also become familiar with pump parts.

FINAL PUMP CHECK

After connecting the piping to pump:

• 

Rotate shaft several times by hand to

be sure that there is no binding and all

parts are free.

•

 Check alignment to determine ab-

sence of pipe strain. If pipe strain

exists,  correct piping.

Figure 15

IMPELLER
ROTATION

WARNING

TO AVOID  SERIOUS INJURY, DO NOT

INSTALL OR SERVICE PUMP UNLESS

ALL POWER  IS OFF AND LOCKED OUT.

AFTER INSTALLATION AND PRIOR TO FIRST OPERATION

ROTATION LABEL
ON MOTOR

MOTOR

Summary of Contents for 200 series






















































Reviews:

No comments