manualshive.com logo in svg

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 22 / 53

Share
Download
Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 22

21

95-03009

TYPE 4 DOUBLE SEAL

The Type 4 Seal is essentially two type 1 seals
assembled back to back in a chamber which bolts
to the backplate in place of the stationary seat
retainer. Except for the additional components,
(e.g. chamber, seals,) Type 1 and Type 4
components are interchangeable. (Figure 31)

CAUTIONS REGARDING HANDLING DAMAGE TO
TYPE 1 APPLY EQUALLY TO THE FOLLOWING
PROCEDURES.

DISASSEMBLY TYPE 4 SEAL

1. 

Shut off and lock out power supply to motor.

2. Close both suction and discharge valves. Remove
seal flush lines from flush housing.
Disconnect the suction and discharge piping from
casing.

3. Remove casing clamp and casing. Remove
backplate O-ring.  Remove the impeller retainer bolt
and O-ring. (Figure 32)

3. Pull impeller, backplate and seal off motor shaft as
a unit. BE SURE NO SHIMS ARE LOST FROM
MOTOR SHAFT.

4. Place impeller assembly FACE DOWN (on impeller
vanes) and remove hex head screws (4) from back of
seal chamber, then carefully lift off seat retainer and
flush housing. (Figure 33)

5. Loosen (2) set screws in the spring retainer and lift
off rotating seal components: rotary seal, O-ring,
washer, spring retainer, springs and washer. 

There

ARE SIX SPRINGS (3 UP and 3 DOWN. )

6. Use backplate to slide rotary seal (next to
backplate) up the impeller shaft approximately
1-1/2 inches. With the backplate resting on the
impeller push the rotary seal toward the backplate
until the O-ring is free. Remove the O-ring and lift
rotary seal off shaft. (See Figure 33)

7. Remove stationary seals and L-gaskets from
backplate and seat retainer.

Note:. The stationary seal  is brittle. Prying or
hammering on the seal plate can shatter the seal.
If the stationary seal  cannot be removed by hand,
place a 2-1/4 inch diameter plastic or wood rod on
the impeller side of the seal and apply even
pressure to dislodge the seal.

8. Inspect and replace all damaged and worn
parts.

Figure 31

Figure 32

HEX HEAD SCREW (4)

SEAT RETAINER

L-GASKET

STATIONARY SEAL

FLUSH HOUSING

ROTARY SEAL

O-RING

WASHER

SPRING RETAINER

SPRING (6)

WASHER

O-RING

ROTARY SEAL

STATIONARY SEAL

L-GASKET

BACKPLATE

IMPELLER

Figure 33

NPT
PORT

SETSCREW

MAINTENANCE

DOUBLE SEAL

O-RING
RETAINER BOLT

CLAMP

O-RING

CASING

DISASSEMBLY FOR CLEANING AND REPAIR

O-RING

O-RING

Summary of Contents for 200 series






















































Reviews:

No comments