manualshive.com logo in svg

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 38 / 53

Share
Download
Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 38

37

95-03009

DESCRIPTION/SPECIFICATIONS

The Waukesha 200 Series Modular Base

Mounted Centrigual Pump design consists of 4

components (in addition to pump and motor).

These components are used in various

combinations and arrangements to provide

flexibility to meet various needs:

* 

Bearing Housing

 (Pump adapter)

•

epoxy coated cast iron w/316 SS shaft, ball

bearings

•

adapter mounts to pump components (same

components used for close coupled pumps)

•

includes coupling for motor shaft plus

guards

•

used in style "B" & "C" arrangements

* 

Motor Adapter

•

epoxy coated cast iron

•

mounts std. NEMA C-face motor onto

bearing housing

•

provides accurate, rigid shaft alignment

•

used in style "B" arrangements

* Stand

•

epoxy coated cast iron stand (pedestal)

•

stand attaches under motor adapter or

bearing housing.

Base (OPTIONAL)

•

epoxy coated channel base - used in style

"B" & "C" arrangements (See page 39)

Figure 3

STYLE C

Bearing housing and base with stand attached to
bearing housing; for use with foot mounted
T- frame motors. Pump and motor are mounted
and supported independently.

STYLE "B" 

Figure 2

Bearing housing, motor adapter and base with
stand attached to bearing housing; for use with
NEMA C-face motors. All motors must have feet
for attachment of supports.

STYLE "C"

 Figure 3

STYLE B

Figure 2

Do Not operate pump

without CASING

clamped securely in place.

WARNING

WARNING

To avoid electrocution,  ALL electrical should

be done by a registered Electrician, following

Industry Safety Standards.

All power must be OFF and LOCKED OUT

during installation.

Waukesha 200 Series

             BASE MOUNT

Summary of Contents for 200 series






















































Reviews:

No comments