manualshive.com logo in svg

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 3 / 53

Share
Download
Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 3

2

95-03009

•

Always lock out power prior to servicing equipment.

•

Ensure pump is isolated from system and pressure is relieved before disassembling
pump, removing plugs, or disconnecting piping.

•

Use proper lifting and supporting equipment to prevent injuries.

•

Observe proper decontamination procedures.

•

Know and follow safety regulations

•

Maintain proper safe working areas.

•

Flanged Connections:  

Never force piping to make a connection with a pump.

•

Do Not operate below minimum rated flow, or with suction/discharge valves closed.

•

Do Not open vent or drain valves, or remove plugs while system is pressurized.

•

Do Not remove casing clamp while system is pressurized.

•

Do Not overtighten casing clamp. 

(Moderate tightening only)

SAFETY

General Safety Instructions:

Waukesha Centrifugal pumps has been designed to be safe and reliable when properly used and
maintained.

•

Do Not operate pump beyond the rated conditions for which the pump was sold.

•

Do Not use heat to remove impeller or disassemble pump due to risk of explosion of
trapped liquid.

•

Do Not operate pump without guards correctly installed.

 • Do Not run pump when *dry.

*Requires Double Seal

•

Wear protective apparel to prevent injuries when handling equipment or product.

Summary of Contents for 200 series






















































Reviews:

No comments