manualshive.com logo in svg

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 5 / 53

Share
Download
Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 5

4

95-03009

WAUKESHA CHERRY-BURRELL WARRANTY

Seller warrants its products to be free from defects in materials and workmanship for a period
of one (1) year from the date of shipment. This warranty shall not apply to products which
require repair or replacement due to normal wear and tear or to products which are subjected
to accident, misuse or improper maintenance. This warranty extends only to the original Buyer.
Products manufactured by others but furnished by Seller are exempted from this warranty and
are limited to the original manufacturer’s warranty.
Seller’s sole obligation under this warranty shall be to repair or replace any products that Seller
determines, in its discretion, to be defective. Seller reserves the right either to inspect the
products in the field or to request their prepaid return to Seller. Seller shall not be responsible
for any transportation charges, duty, taxes, freight, labor or other costs. The cost of removing
and/or installing products which have been repaired or replaced shall be at Buyer’s expense.
Seller expressly disclaims all other warranties, express or implied, including without limitation
any warranty of merchantability of fitness for a particular purpose. The foregoing sets forth
Sellers entire and exclusive liability, and Buyer’ exclusive and sole remedy, for any claim of
damages in connection with the sale of products. In no event shall Seller be liable for any
special consequential incidental or indirect damages (including without limitation attorneys’
fees and expenses), nor shall Seller be liable for any loss of profit or material arising out of or
relating to the sale or operation of the products based on contract, tort (including negligence),
strict liability or otherwise.

WARRANTY

GENERAL INFORMATION

MANUAL FORMAT

This manual is laid out in sections. Each section addresses specific subjects. Familiarize yourself with the
subjects by scanning through the manual. Whether installing, operating, troubleshooting, maintaining or
ordering parts, read through that section and follow instructions.

ORDERING/RETURNING PARTS

See page 50 for complete information on ordering and returning parts. Record EQUIPMENT and DISTRIBUTOR
INFORMATION immediately.

SHIPPING DAMAGE

Inspect your shipment immediately. If damage is found, note it on the drivers copy (packing slip) and request
the driver to ask the Inspector to call. You are responsible for initiating shipping damage claims.

HIDDEN DAMAGE OR WARRANTY CLAIM

If during installation, you discover apparent shipping damage, contact the Shipper immediately and ask for
an Inspector to call. Notify your Distributor of the problem. In warranty claims you must have a returned goods
authorization from the manufacturer before any returns will be accepted. Your Distributor will help you with
a warranty problem. Please read the Warranty statement.

Summary of Contents for 200 series






















































Reviews:

No comments