manualshive.com logo in svg

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 44 / 53

Share
Download
Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 44

43

95-03009

PRE-ASSEMBLED SEALS

Pre-assembled (Cartridge) Seals have all of the

seal components mounted to a flange. They are

pre adjusted at factory. Follow the Seal

Manufacturers's (John Crane, A. W. Chesterton,

etc.) recommendations regarding application,

operation and maintenance.

The following procedures apply to this type of

seal:

DISASSEMBLY

1. Remove all flush connections and fittings.

Remove the casing clamp, casing and O-ring

from the housing flange. (Figure 11)

2. Remove the impeller retainer bolt and O-

ring; then loosen the seal setscrews-and pull the

impeller, backplate and seal off the bearing

shaft as a unit. Set the assembly face down

 (on

the impeller).

 (Figure 11-12)

Note: The clearance shims that position the

impeller within the casing are at the end of the

impeller hub (inside the seal.) Keep shims

together as a set for reassembly. 

(Figure 12)

3. Remove the seal unit from the backplate

assembly by removing the cap screws holding

the seal flange to the seal adapter. Pull seal

from seal adapter. Remove seal adapter by

removing socket head cap screws holding

adapter to the back plate. (Figure 12)

PUMP ASSEMBLY

1. Place shims, backplate and impeller on

the shaft assembly. Hand tighten the impeller

retainer bolt on the shaft.

2. Check the space between the back of the

impeller and the backplate with a feeler gage

(.030 nominal) while holding the backplate tight

against the bearing housing flange.

 (Any axial

movement of the shaft should not be added to

the .030 nominal clearance.)

 If needed, change

this clearance by adding or removing shims.

(Figure12-13) Confirm operating clearances by

clamping the casing to the bearing housing

flange and rotating the shaft/impeller manually

to be sure the impeller does not touch the casing

or backplate. When proper shim pack is

confirmed 

remove

 the casing, impeller and

backplate leaving the shim pack on the shaft.

3. Insert L-gasket into the backplate. Insert

cartridge adapter into the backplate and tighten

with four socket head cap screws. (Figure 14)

IMPELLER BOLT
ASSEMBLY

O-RING

.030'

Figure 13

Figure 12

Figure 11

Figure 14

BACKPLATE

SHIMS

CARTRIDGE
 SEAL

SOCKET

         HEAD

 CAPSCREW

IMPELLER

CAP SCREW

ADAPTER

CLAMP

CASING

ADAPTER

SOCKET HEAD
CAP SCREW

L-GASKET

CARTRIDGE SEALS

                                 REMOVAL /  ASSEMBLY

SET SCREWS

BACKPLATE

Summary of Contents for 200 series






















































Reviews:

No comments