manualshive.com logo in svg

Waukesha 200 series, Operation, Maintenance And Parts Manual, Page: 19 / 53

Share
Download
Waukesha 200 series Operation, Maintenance And Parts Manual Download Page 19

18

95-03009

MOTOR OVERLOAD CONDITIONS

Centrifugal pump motors may overload

 (draw excessive

electrical current)

 under certain conditions. This will trip

motor overload protection or burn out motor.

Certain combinations will overload motor when operated

with open, unrestricted discharge which results in too

high flow rate. Additional discharge restriction may be

required to lower flow rate and lower horsepower

requirements with . 

DO NOT

 add restriction to supply

line. 

(If pump was incorrectly selected, a smaller impeller

may be required or a higher motor horsepower may be

required.)

AMMETER TEST

If uncertain about pump selection and application, the electrician

should temporarily install an ammeter in the electrical service to

determine motor load.

Operate pump under process conditions and check motor amp draw

versus nameplate full load rating. If amp draw exceeds motor rating,

a system change or pump change is required.

If process conditions and/or liquid changes (higher viscosity, higher

specific gravity) recheck motor amp draw.

Contact your authorized Waukesha Cherry-Burrell Distributor for

assistance.

(See PARTS ORDERING page 50 for information.)

TROUBLESHOOTING

   MOTOR OVERLOADING

Summary of Contents for 200 series






















































Reviews:

No comments