background image

29

POWER SOURCES

When installing electrofusion fittings in field applications, it is necessary to have a reliable source of 

AC power for the processor. This AC power source should:

 

•  be well maintained and subjected to a periodic maintenance schedule.

 

•  provide output voltage within the specified operating range.

 

•  contain a matching outlet, which is required to connect with the plug equipped on the          

   processor.

Utility Power

Utility power is a reliable and ideal power source for the 

Rionfuser Electrofusion Processor

. How-

ever, it is not practical to gain access to this kind of power source in field applications. When fusing 

with utility power, a dedicated connection to the service panel is recommended because the potential 

amperage draw is very high.

Generators

Fuel powered generators are also a good source of electrical power for the 

Rionfuser Electrofu-

sion Processor

. Always make a note of the minimum fitting power requirements. Additional power 

capacity is recommended for intangibles (i.e. powering other accessories, wear & tear, etc.). Before 

starting a fusion, it is important to make sure:

 

•  the generator has enough fuel to complete the electrofusion cycle.

 

•  the auto-throttle is disengaged (in anticipation of immediate power draw).

Inverters

Inverters are an acceptable AC power source for the 

Riofuser Electrofusion Processor

, though 

some produce output waveforms that are troublesome with specific fittings. We recommend perform-

ing compatibility tests using the lightest and heaviest anticipated loads before approving an inverter 

system. Feel free to contact us to discuss issues regarding the use of inverters.

Power Specifications

Extension Cords

Because electrofusion fittings produce a high amperage draw, the use of an extension cord is not 

encouraged. In the event such usage is necessary, the following lengths and wire gauges are recom-

mended:

Extension cords should not be used when fusing multiple fittings at the same time.

Cord Length

Wire Gauge

Less than 25 feet

12/3

Less than 50 feet

10/3

Less than 100 feet

8.3

Supply Voltage

97 VAC to 150 VAC

Supply Frequency

47 Hz to 70 Hz

Supply Waveform

Sine Wave or Square Wave

Output Current

20 Amps AC

Output Voltage

95 volts AC at 120 Volts Input

Summary of Contents for ORION Rionfuser




































Reviews: