background image

25

Downloading Data

Data Stored

The following data is stored for each fusion that the processor performs. Depending on the processor 

model, data stored in the processor can be downloaded to a USB Flash drive or wirelessly via Blue-

tooth with the EF Utilities app.

Field

Description

SN

The serial number of the processor.

Fusion #

The fusion number.

User Fusion #

 The user resettable fusion counter.

Date

Date and time the fusion was performed.

Cal Due

The date the calibration is due.

Cal Req.

TRUE if the calibration date was expired when the fusion was completed.

Firmware

The firmware version of the processor loaded when the fusion was per-

formed.

Result

The resulting error code.

Mode

The mode used for entering the fusion parameters.

Fitting

The fitting manufacturer type and size.

Control

The requested fusion output voltage.

Temp

The ambient temperature at the time of the fusion.

Nom. Time

The requested fusion time.

Comp Time

The fusion time after temperature compensation was applied.

Actual Time

The actual time the fitting was fused.

Mea Res

The resistance of the fitting specified in the barcode.

Tolerance

The specified resistance tolerance.

Mea Res Pre

The actual measured resistance of the fitting before the fusion.

Mea Res Post

The actual measured resistance of the fitting after the fusion.

Cooling Time

The cooling time of the fitting specified in the barcode.

ID Res.

The measured value of the ID Resistor for ID Resistance fusions.

Input Volts 

The measured generator voltage taken before the fusion.

High Volts

The highest measured generator voltage during the fusion.

Low Volts

The lowest measured generator voltage during the fusion.

Wave

The type of supply waveform identified during the fusion (Sine or Square).

Frequency

The measured generator frequency made before the fusion started.

High Freq

The highest measured generator frequency during the fusion.

Low Freq

The lowest measured generator frequency during the fusion.

L Out V

The lowest measured output voltage during the fusion.

H Out V

The highest measured output voltage during the fusion.

L Out A

The lowest measured output current during the fusion.

H Out A

The highest measured output current during the fusion.

Ah Out

The total number of Amp-Hours expended during the fusion.

Summary of Contents for ORION Rionfuser




































Reviews: