background image

WL2FL 

Manual

 

Page 81 – Revision AUS-04-23

 

 

 

Installation 

It is advised to turn off the water supply to the machine and disconnect the water supply during 

these steps to make it easier to manoeuvre the machine. If you have enough working space around 

you, this step is not necessary. 
Safely isolate the WL2FX from the main power supply. To do this, remove the power plug from the 

mains socket and unplug the other side of the power harness from the back of the machine. Place the 

power lead in a safe position away from any water or trip hazard locations – It is recommended to 

place in your tool bag. 

For Mini Models only

: Using appropriate personal protective equipment, drill 17mm hole into the 

back of the machine as per below location. Take extreme caution while doing this task. 

 
 
 
 
 
 

 

For Free Standing models only:

 Carefully knock through the knockout hole for the pedal wire harness 

to go through. It may be necessary to enlarge the knockout hole using a 17mm drill bit for the 

grommet to fit appropriately. 

 
 
 
 
 
 
 

Fit the rubber grommet into the hole that has either been drilled for mini models or knocked out for 

free standing models. The grommet is used to protect the harness as it goes through the machine. 
 
For newer freestanding and mini models, the cut out and grommet has already been pre installed for 

you and there is no need to follow the above steps. 
 
 
 
 

 

 

 

Summary of Contents for PUREZZA WL2FL FIREWALL


















































































Reviews: