W&H Lisa VA131-17 Instructions For Use Manual Download Page 57 | Manualshive

Page: 57 / 140

background image

Sterilization cycles

LISA | Instructions for Use | VA131 2019 ENG Rev06 | 16/04/2020 | © 2020 W&H Sterilization Srl

57

CONTENTS

This section deals with the following subjects:

Load maintenance and preparation

Prepare the sterilizer

Sterilization cycle description

Sterilization cycle management

Sterilization cycle report

Load maintenance and preparation

WARNINGS

WARNING! Any residual of chemicals (like cleaning and
disinfection products), could affect the purity of the steam
and consequently the whole sterilization process.
If necessary, the load shall be cleaned and lubricated in
accordance with the instrument manufacturer’s
instructions.

Notice: Any residual of chemicals could seriously damage the
sterilizer. The manufacturer’s warranty is void in case of damage
caused by chemicals.

DENTAL HANDPIECES EXTERNAL DISINFECTION

This procedure reduces the risk of infection during cleaning and
maintenance of the dental handpieces.

n

Wear protective gloves during disinfection.

n

Avoid using abrasive disinfectants (pH-value 2.5 – 9; no
chlorine based disinfectants).

n

Use disinfectant wipes rather than spray disinfection.

n

Do not immerse handpieces in disinfectants.

n

Residual disinfectants on handpieces can cause extensive
damage to your instrumentation during sterilization (oxidation,
alteration of technical characteristics of seals, rubbers, fiber
optics, etc.)

«
...
55
56
57
58
59
...
»

Summary of Contents for Lisa VA131-17













































































































































Reviews:

No comments

Related manuals for Lisa VA131-17

Brand: Rangevision Pages: 31

Brand: 1010music Pages: 2

Brand: 1010music Pages: 4

Brand: Abbott Pages: 2

FreeStyle Libre

Brand: Abbott Pages: 3

Brand: abc Pages: 8

Brand: CAB Pages: 13

Brand: CAB Pages: 30

Brand: CAB Pages: 17

Brand: CAB Pages: 33

Camping Equipment

Brand: C. Crane Pages: 8

Brand: C-Pro Direct Pages: 4

Brand: C-Pro Direct Pages: 4

Brand: Federal Signal Corporation Pages: 4

Brand: ParaBody Pages: 7

Brand: NEILPRYDE Pages: 55

Brand: HANYOUNGNUX Pages: 4

Brand: Park House Healthcare Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands