W&H Lisa VA131-17 Instructions For Use Manual Download Page 102

Page: 102 / 140

Diagnostics

102

Code

Description

Actions

3xx

Check the door gasket. Clean or replace it if necessary.

Repeat the cycle.

If the problem persists, call service.

Clean the chamber face side.

Clean the chamber filter.

Check if chamber filter is properly locked in the cap.

Check the load does not exceed the MAXIMUM WEIGHT LIMITS.

4xx

Clean water error (bad quality or low water level). Drain and refill the clean water tank.

Repeat the cycle.

If the problem persists, call service.

5xx

Check if there are hurdles on the door locking area (chamber rack, loads, objects, …).

Repeat the cycle.

If the problem persists, call service.

Check the door gasket (wrong placed).

Check if the door can move freely without touching the trays or the load when closing.

Switch the sterilizer OFF and ON.

990

The cycle has been aborted by the user.

Re-process the load.

MESSAGES AND ALERTS

Notice: For any error not listed in this table, call technical service.

Message/Alert

Description

Action

Fill clean water tank.

There is not enough water in the tank to perform a
cycle.

Fill the water tank as requested.

Drain used water tank.

The used water tank is full.

Drain the water tank as requested.

Please close the door.

The door must be locked, but you didn't close it.

Close the door so it can be locked.

Summary of Contents for Lisa VA131-17













































































































































Search results

Summary of Contents for Lisa VA131-17

Reviews:

Related manuals for Lisa VA131-17

Brands by name

Popular brands

W&H Lisa VA131-17, Instructions For Use Manual

Search results

Summary of Contents for Lisa VA131-17

Reviews:

Related manuals for Lisa VA131-17

Brands by name

Popular brands