W&H Lisa VA131-17 Instructions For Use Manual Download Page 42

Page: 42 / 140

Managing printers

CONTENTS

This section deals with the following subjects:

Printer selection (optional)

Label printer selection (optional)

Label printer usage (optional)

Label content description

Printer selection (optional)

SELECT THE PRINTER

Note: The sterilizer only supports the specific printer models available
through manufacturer/importer.

On the homepage tap

Tap the model of the printer to use.

Tap

to confirm and go back to

the previous page.

Label printer selection (optional)

FUNCTION AVAILABILITY

The first time you access the Label Printer (

) menu, you will be

requested to enter an activaction code. To require the activation
code, please refer to the Activation code instructions provided with
the label printer.

LABEL PRINTER SETUP

Labels can be printed by a local label printer or (only with a LAN
connection set) a shared label printer. The local label printer is

Summary of Contents for Lisa VA131-17













































































































































Search results

Summary of Contents for Lisa VA131-17

Reviews:

Related manuals for Lisa VA131-17

Brands by name

Popular brands

W&H Lisa VA131-17, Instructions For Use Manual

Search results

Summary of Contents for Lisa VA131-17

Reviews:

Related manuals for Lisa VA131-17

Brands by name

Popular brands