W&H Lisa VA131-17 Instructions For Use Manual Download Page 106

Page: 106 / 140

106

Diagnostics

ERROR PAGE

During the sterilization cycle, the sterilizer is continuously
monitored by a control system. If an anomaly is detected, the cycle
is aborted automatically, and the sterilizer starts a reset phase.

The following page appears:

Part

Description

Current sterilization cycle

Error number, See "Errors"
on page 100.

Warning messages.

Open button that appears
after the reset phase had
finished.

WARNING MESSAGES

Message

Description

Load not
sterile

The load is not sterile.

WARNING! Do not use items on patients!

Drying
interrupted

The load might be wet.

WARNING! Wet items are for immediate use only!

Summary of Contents for Lisa VA131-17













































































































































Search results

Summary of Contents for Lisa VA131-17

Reviews:

Related manuals for Lisa VA131-17

Brands by name

Popular brands

W&H Lisa VA131-17, Instructions For Use Manual

Search results

Summary of Contents for Lisa VA131-17

Reviews:

Related manuals for Lisa VA131-17

Brands by name

Popular brands