manualshive.com logo in svg

WAGO 765-4203/0100-0000, Product Manual

Share
Download
WAGO 765-4203/0100-0000 Product Manual Download Page 64

765-4203/0100-0000

Commissioning

64

Product manual | Version: 1.0.0
4PORT IOL-A FLD EC DC 24V 2.0A

ð

The IP address has been set.

10.2 Configuration

10.2.1 Configuring EtherCAT

To configure the EtherCAT

®

 master, you need the ESI (EtherCAT

®

 Slave Information)

files in XML format:

WAGO_series765.xml

 and 

WAGO_series765_diag.xml

The file 

WAGO_series765.xml

 contains a reference to the file 

WAGO_se-

ries765_diag.xml

, which contains diagnostic texts. Perform the following steps in the con-

figuration software of the EtherCAT

®

 master used:

• Import the XML files.
• Select the module from the device catalog.
• Configure the ports
• Set the parameters.

10.2.1.1 Selecting the Module

Select the module used from the device catalog.

Module: 0765-4203/0100-0000

Designation:4 PORT IOL-A FLD EC 24 VDC 2.0 A

10.2.1.2 Configuring a Port

In the configuration software of the EtherCAT master, each IO-Link port of the 765 mod-
ule corresponds to a slot. For each IO-Link port X01/X02/... , specify what is connected to
it:
• IO-Link device and how much process data it transmits
• Digital Input
• Digital Output
• whether nothing is connected

The following table lists the selection options for the device type connected to IO-Link
port X01/X02/... .

Table 44: Configuration of the IO-Link Port

Slot/Module

Description

Clear slot

Nothing is connected to the IO-Link port.

Digital_IN

Digital input (pin 4).

Digital_OUT

Digital output (pin 4).

IOL_1/0_I/O byte

IO-Link device with 1 bytes of of input process data

IOL_2/0_I/O byte

IO-Link device with 2 bytes of of input process data

IOL_4/0_I/O byte

IO-Link device with 4 bytes of of input process data

IOL_8/0_I/O byte

IO-Link device with 8 bytes of of input process data

IOL_16/0_I/O byte

IO-Link device with 16 bytes of of input process data

IOL_32/0_I/O byte

IO-Link device with 32 bytes of of input process data

IOL_0/1_I/O byte

IO-Link device with 1 bytes of output process data

IOL_0/2_I/O byte

IO-Link device with 2 bytes of output process data

Summary of Contents for 765-4203/0100-0000



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands