manualshive.com logo in svg

WAGO 765-4203/0100-0000, Product Manual

Share
Download
WAGO 765-4203/0100-0000 Product Manual Download Page 48

765-4203/0100-0000

Planning

48

Product manual | Version: 1.0.0
4PORT IOL-A FLD EC DC 24V 2.0A

Index Subindex

Parametername

Value Range

Default Description

0x8000.20,

0x8010.20,

...

IO-Link port X01/
X02/...

IO-Link Revision

0, 16, 17

0

Check of the IO-Link version:

0: no check

16: checking whether the connected
IO-Link supports specification V1.0.

17: checking whether the connected
IO-Link supports specification V1.1.

0x8000.21,

0x8010.21,

...

IO-Link port X01/
X02/...

Frame Capability

0

0

Not supported: no function.

0x8000.22,

0x8010.22,

...

IO-Link port X01/
X02/...

Cycle time

0, 4 ... 191

0

Port Cycle Time

0: calculated by IO-Link master
4 ... 191: see following table

0x8000.23,

0x8010.23,

...

IO-Link port X01/
X02/...

Offset Time

0

0

Not supported: no function.

0x8000.24,

0x8010.24,

...

IO-Link port X01/
X02/...

Process Data Input
Length

0 ... 223

0

Length of the input data

Set automatically by the configuration
software. Please do not change.

0x8000.25,

0x8010.25,

...

IO-Link port X01/
X02/...

Process Data Out-
put Length

0 ... 223

0

Length of the output data

Set automatically by the configuration
software. Please do not change.

0x8000.26,

0x8010.26,

...

IO-Link port X01/
X02/...

Compatible ID

0

0

Not supported: no function.

0x8000.27,

0x8010.27,

...

IO-Link port X01/
X02/...

Reserved

0

0

Reserved

0x8000.28,

0x8010.28,

...

IO-Link port X01/
X02/...

Master Control

0 ... 4, 36, 68

0

Bits 0 … 4:

0: IO-Link port inactive.
1: Pin 4 is a digital input.
2: Pin 4 is a digital output.
3: IO-Link communication enabled
without compatibility check.
4: IO-Link is enabled if the connected
IO-Link device is compatible.

Bits 4 … 15:

2: data storage enabled.
4: data storage disabled.

The “Port cycle time” parameter contains a factor (bits 0 to 5) and time basis (bits 6 and
7). The following table describes how the port cycle time is calculated from the factor and
the time basis.

Table 42: Calculation of Port Cycle Time

Value Range

Time Basis (Bits
6+7)

Factor (Bits 0–5)

Port Cycle Time
(Formula)

Examples

4 ... 63

0.1 ms (00)

4 ... 63

0.1 ms * factor

4: 400 μs

16: 1.6 ms

Summary of Contents for 765-4203/0100-0000



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands