![background image](http://html1.mh-extra.com/html/wacker-neuson/ez17/ez17_operators-manual_3134811248.webp)
39
Machine Shutdown
Properly shutting down a compact excavator can help
prevent accidents when the machine is left unattended.
Shut down the excavator following the specific
procedures in the manufacturer’s operator manual.
A typical list includes:
— Stop the machine.
— Make sure the area around the machine is clear of
personnel.
— Slew the machine to align the upperstructure with the
undercarriage, if possible.
— Return controls to neutral, including the auxiliary
hydraulic controls.
— Lower the attachment and blade to the ground with
slight down-pressure.
— Idle engine for a short cool-down period.
— Stop the engine.
— Cycle all hydraulic controls to relieve system pressure.
— Engage the control locking device, if equipped.
— Remove ignition key.
— Block the tracks if on a slope or incline.
— Check for and clean out trash build-up, especially in
the engine compartment, battery box, around
exhaust components, in confined spaces, under the
machine and around rotating components.
Safe Dismounting
Never dismount from moving equipment. Observe
proper shutdown practices before dismounting. Check
for slippery steps and handholds.
Dismount carefully using three-point contact facing the
machine. (See page 21,
Mount And Dismount Properly
.)
Shut Down Safely
Lower
Attachment
Shut Off Engine,
Remove Key, Engage
Control Lock
40
Load And Unload The Machine Safely
Loading And Unloading For Transport
All machines are not loaded in the same way, and the
procedures given in the manufacturer’s manual(s) should
always be followed.
Some precautions apply to all machines:
— Keep bystanders away.
— Wear the seat belt, if equipped.
— If the compact excavator is equipped with a foldable
TOPS/ROPS, make sure it is properly secured in the
raised position.
— Place transport vehicle on a firm, level surface.
— Block or support the rear of the trailer.
— Secure the parking brake and block transport vehicle
so it cannot move.
— Use ramps with slip-resistant surfaces, adequate size
and strength, low angle (15 degrees or less) and
proper height.
— Keep trailer bed and ramps clear of mud, oil, ice,
snow, leaves and other debris.
— Position the attachment to the front of the machine.
— Drive forward up the ramps, raising the blade high
enough for clearance.
— Cover or remove any SMV (Slow-Moving Vehicle)
emblem.
— Secure the cab door, attachment and accessories in
the transport position.
— Engage upperstructure slew lock, if equipped.
— Chain and block the excavator securely for transport.
Refer to the manufacturer’s operator manual for
tie-down procedures.
Measure the transport height and width of the loaded
machine to avoid overhead and width obstructions.
Make sure clearance flags, all lights and warning signs
are in place and visible.
Keep
Bystanders
Away
Read
Operator Manual
Summary of Contents for EZ17
