Wabtec Ricon K2005 Page 74 Service Manual Download

Page: 74 / 76

4 - 29

SPARE PARTS

JUNE 2021

32DSKF02.D

TITANIUM S-SERIES AND K-SERIES

PUBLIC USE SERVICE MANUAL

FIGURE 4-8: TITANIUM S-SERIES & K-SERIES DOT PUBLIC USE HANDRAILS ASSY

FIG.
ITEM DESCRIPTION

QTY CONFIG. PART

NO.

BUMPER, RUBBER (BAG OF 10)

20653

CAP, ROUND, BLACK

25550

HANDRAIL, LH

(

REFERENCE ONLY

)

REF

32989

HANDRAIL, RH

(

REFERENCE ONLY

)

REF

32988

KIT, BUCKLE ASSY, w/ SWITCH

46589

SCREW, SHOULDER, HEX HD,10-24 X 3/4, SST

(

REFERENCE ONLY

)

REF

46033

STRAP ASSY, STRAIGHT SLIDER

46590

SCREW, HEX, 5/16-18 X 1 SST (BAG OF 10)

19706

SCREW, HEX, 5/16-18 X 1 1/2 SST (BAG OF 10)

14413

SPACER, TRANSIT HANDRAIL

V2-AC-063

LIGHT ASSY, WHITE LED, PLATFORM

46011

SCREW, PHP, 8TEK X 3/4 (BAG OF 10)

15911

HARNESS, BELT & HANDRAIL LIGHT

37348

HARNESS EXTENSION, HANDRAIL LIGHT

37346

KIT, HARNESS BELT RESTRAINT, W/SLP TERMS

01274

NOTE

: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts.

NOTE

: * Item or configuration not shown.

Summary of Contents for Ricon K2005













































































Search results

Summary of Contents for Ricon K2005

Reviews:

Related manuals for Ricon K2005

Brands by name

Popular brands

Wabtec Ricon K2005, Service Manual

Search results

Summary of Contents for Ricon K2005

Reviews:

Related manuals for Ricon K2005

Brands by name

Popular brands