voran EP 1000 Operating Manual Download Page 8 | Manualshive

Page: 8 / 40

voran EP 1000 Operating Manual Download Page 8

De-stoning machine EP 1000

Version: 136401000_M0014772F_EN400/50D
Datum: 15.01.2021

- 8 / 40 -

1.5.2 Normal Operation

NOTE!

Avoid working methods that are not clear from a safety aspect!
Make all required settings to the machine/line so that can work under reliable and safe operating
conditions!
The machine/line may only be operated when all safety devices and safety equipment is available
and functional, such as e.g.:

- emergency stop button

- two hand operation (dead man's switch)

- protective covers

- safety switches

- personal safety equipment

WARNING AGAINST GENERAL DANGERS

Make a visual check of the machine / line before each start for externally visible damage or
defects! All changes (also including changes to the Operating Manual) must be documented
immediately and the person in charge and/or the customer service must be informed.

The machine / line is to be

brought to an immediate standstill and secured against being

started up again!

In the event of malfunctions the machine / line must be shut down at once and locked against
being restarted!

Ensure that the malfunction is dealt with immediately and professionally!
Observe the on and off switching processes and compare the monitoring displays with the data
provided in the documentation/Operating Manual!
Observe all the signs fixed to the machine / line!

Before starting up the machine / line it must be ensured that no persons are in danger!
Do not remove any safety covers while the machine / line is in operation!
Moving mechanical parts must not be touched!

Do not use electrical cut-outs that do not comply with the required fuse-protection!
In the event of an electricity supply failure the machine / line is to be shut down immediately!

In order to ensure a smooth and uninterrupted operation the machine / line and its surroundings
are to be kept clean and tidy and adequate lighting must be provided in the working area.

Before beginning normal operation a functional test of all functional groups and safety equipment
must be made without fail!

«
...
6
7
8
9
10
...
»

Summary of Contents for EP 1000









































Reviews:

No comments