voran EP 1000 Operating Manual Download Page 3 | Manualshive

Page: 3 / 40

voran EP 1000 Operating Manual Download Page 3

De-stoning machine EP 1000

Version: 136401000_M0014772F_EN400/50D
Datum: 15.01.2021

- 3 / 40 -

1

Basic safety principles

1.1 Key to the symbols

Listing of the symbols used and their significance

BEFORE FIRST START INSTRUCTIONS READ

Not observing this requirement can lead to serious injury or to death!

WARNING OF DANGEROUS LIVE ELECTRICAL POWER SUPPLY

Before any servicing or checking work is undertaken, all parts or supply lines on the machine that
are marked with this sign must be switched free from live current.

Not observing this requirement can lead to serious injury or to death!

WARNING AGAINST BEING DRAWN IN

The removal of safety components and the non-observation of safety regulations during operation
is forbidden!
Maintain safety distance to revolving parts! Loose parts of clothing, arm or neck chain jewellery
can become caught in moving machine parts during servicing or repair work. If hair is worn long a
hairnet must be used to prevent hair from becoming caught or pulled in.

Not observing this requirement can lead to serious injury or to death!

BEFORE OPENING UNPLUG!

Interrupting your work on the machine power supply and secure against accidental before
reconnecting it and turning.

Non compliance can mean severe personal injury.

WEAR EAR MUFFS!

Ear muffs must be worn when there is a high noise level!

Not observing this can lead to serious personal injury!

«
1
2
3
4
5
...
»

Summary of Contents for EP 1000









































Reviews:

No comments