voran EP 1000 Operating Manual Download Page 5 | Manualshive

Page: 5 / 40

voran EP 1000 Operating Manual Download Page 5

De-stoning machine EP 1000

Version: 136401000_M0014772F_EN400/50D
Datum: 15.01.2021

- 5 / 40 -

1.2 General safety regulations

NOTE!

Ensure that the machine/line is only operated under perfect technical operational conditions and
giving full account to the proper use.

WARNING AGAINST GENERAL DANGERS

Ensure that all possible faulty functions and risk situations are eliminated immediately and without
delay before starting up!

Faulty functions and risk situations are e.g.:

uncontrolled lifting/sinking and turning/swivelling movements

loose parts on the machine/line

INFORMATION!

Not following the instructions in this Operating Manual can lead to the loss of your warranty!

Mind the present accident prevention regulations of the e

m

ployer's liability insurance associations

and other rules, e.g. VDE, IEC

1.3 Selection, qualification and responsibility of operating staff

NOTE!

Please note each operator of the unit must be trained, instructed and older than 15 years.

Please observe your national law and regulations for industrial safety.
Operating staff who are in training or under instruction may only work under the constant
observation of an experienced person who is thoroughly familiar with this machine/line!

All work on the electrical systems for this machine/line may only be carried out by a qualified
electrician / electrical engineer. All work of this kind may only be carried out under the direction of a
qualified electrician / electrical engineer taking full account of the relevant electro-technical
guidelines.

The operating personnel must ensure that no other people are in the working area.

Before you leave the unit, you have to stop it and to ensure that no unauthorized person
(especially children) is able to restart it. Therefore lock the main switch in position <0> with a
padlock and / or disconnect the main plug!

«
...
3
4
5
6
7
...
»

Summary of Contents for EP 1000









































Reviews:

No comments