manualshive.com logo in svg

voran EP 1000, Operating Manual, Page: 18 / 40

Share
Download
voran EP 1000 Operating Manual Download Page 18

De-stoning machine EP 1000 

 

Version: 136401000_M0014772F_EN400/50D 
Datum: 15.01.2021

 

                     - 18 / 40 -

 

 

 

4.2  Controls and settings work before first starting up/re-starting of line 

 

Check the machine/line for loose parts (e.g. forgotten tool)! 
 
Check all cable connections (clamp and plug connections) as also all pneumatic pipelines of the machine/line. Pay 
particular attention to damaged and loose cable and connections (see illustration) 
 

Check that the required safety devices have been placed in an orderly manner and are intact! (see the 
chapter "Safety devices")

 

 

WARNING AGAINST GENERAL DANGERS

 

 

 

Before cleaning the device or checking the connection cable, to see if this has been twisted or 
damaged, switch the machine off 
without fail and pull out the mains connector plug! 

 
 

 

Picture 4.2-1) Symbol image, control cable and connector point

 

 
Changes in comparison with normal operation such as 
 
-  higher capacity feeding 
-  higher noise development 
-  higher acceleration or delay, higher vibration amplitudes 
-  unusual noises or unusual smells 
-  response of the safety devices without a motivational cause 
 
are grounds for recognising that the function of the line/machine is impaired. 
Detrimental effects such as this or similar are to be immediately reported by the operator to the person responsible. 

 

 

Optische_Kontrolle_Kabel_Leitungen_1PSM

Summary of Contents for EP 1000









































Reviews:

No comments