Volvo Penta D25A MS Operator'S Manual Download

Page: 58 / 87

Maintenance: Lubrication system

Lubrication oil by-pass filter
change

1. Stop the engine

2. Unscrew the oil filter using a special filter wrench.

Note!

Place a container beneath the filter when remo-

ving to avoid oil spill.

Warning!

Hot oil can cause burns.

3. Lightly oil the new filter’s rubber gasket and check

its mating surface on the mounting.

4. Screw on the new filter by hand until the gasket is

in contact with the sealing surface. Then tighten
the filter a further approximately 3/4 of a turn
using a filter wrench.

Hydraulic governor oil filter change

1. Place a drip pan under the governor oil filter.

2. Loosen the screw holding the pipe connecting the

oil filter and the governor (1).

3. Remove the pipe (2).

4. Open the air vent plug (3) so that the rest of the

remaining oil flows into the oil drip pan.

5. Remove the center bolt (4), remove the old filter

and mount a new.

6. Remove the air vent plug and fill the filter housing

with new oil.

7. Tighten the air vent plug.

Plus d'informations sur : www.dbmoteurs.fr

Summary of Contents for D25A MS
























































































Search results

Summary of Contents for D25A MS

Reviews:

Related manuals for D25A MS

Brands by name

Popular brands

Volvo Penta D25A MS, Operator'S Manual

Search results

Summary of Contents for D25A MS

Reviews:

Related manuals for D25A MS

Brands by name

Popular brands