Volvo Penta D25A MS Operator'S Manual Download

Page: 27 / 87

Operation

Start using auxiliary batteries

WARNING!

Ventilate well. Batteries generate

oxyhydrogen gas, which is extremely flammable
and explosive. A short circuit, naked flame or
spark can cause a powerful explosion.

Never reverse the polarity of the battery. Risk of
sparks and explosion.

1. Make sure the rated voltage of the auxiliary bat-

tery is the same as the system voltage of the
engine.

2. Connect the red auxiliary cable to the discharged

battery’s + terminal and then to the auxiliary
battery’s + terminal.

3. Connect the black jump lead to the auxiliary bat-

tery negative terminal and then to a position
slightly away from the discharged batteries, for
example at the negative cable’s connection to the
starter motor.

WARNING!

The black auxiliary cable (–) must not

come in contact with the positive connection on
the starter motor.

4. Start the engine and run at fast idling speed for

about ten minutes to charge the batteries.

WARNING!

Working on or approaching a running

engine is a safety hazard. Beware of rotating
parts and hot surfaces.

WARNING!

Do not touch the connections while

attempting to start; Risk of sparks. Do not bend
over the batteries either.

5. Stop the engine. Remove the auxiliary cables in

reverse order to connecting.

Plus d'informations sur : www.dbmoteurs.fr

Summary of Contents for D25A MS
























































































Search results

Summary of Contents for D25A MS

Reviews:

Related manuals for D25A MS

Brands by name

Popular brands

Volvo Penta D25A MS, Operator'S Manual

Search results

Summary of Contents for D25A MS

Reviews:

Related manuals for D25A MS

Brands by name

Popular brands