Volvo Penta D25A MS Operator'S Manual Download Page 51

Page: 51 / 87

Maintenance: Fuel System

Fuel control

Fuel control link joints inspection

Check the ball joints for play. If there is more than
0.1 mm [0.004in.] play, replace the ball joints with
new ones.

WARNING!

In case of a control link having ball

joints that is an integral part of the link, change
the link as an assembly.

Injection pump control rack operation

Move the stop lever back and forth a few times and
find out if the control rack can be operated smoothly.

WARNING!

If the rack sticks this must be fixed

before starting the engine.

WARNING!

Never try to control the engine rpm

by moving the manual stop control leaver in the
opposite direction of the arrow. This casn result
in serius harm of the installation.

Plus d'informations sur : www.dbmoteurs.fr

Summary of Contents for D25A MS
























































































Search results

Summary of Contents for D25A MS

Reviews:

Related manuals for D25A MS

Brands by name

Popular brands

Volvo Penta D25A MS, Operator'S Manual

Search results

Summary of Contents for D25A MS

Reviews:

Related manuals for D25A MS

Brands by name

Popular brands