Volvo Penta D25A MS Operator'S Manual Download Page 39 | Manualshive

Page: 39 / 87

background image

39

Maintenance: General

Recommendation of Daily Operation Records

Items to be recorded

The following items are recommended to be recorded
once a day:

1. Operating hours.

2. The amount of lubrication oil and coolant (fresh

water) required for refilling. Fuel consumption.

3. Lubrication oil and coolant (fresh water) change

intervals.

4. Lubrication oil pressure and temperature, engine

rpm, exhaust temperature, coolant temperature,
and charge air temperature and pressure.

5. Seawater pressure and seawater temperature

before and after heat exchanger. Ambient
temperature and engine room temperature at
turbo charger inlet.

6. Parts serviced and kinds of service (adjustment,

repairs, or replacement).

7. Change in operating conditions (for example,

“Exhaust smoke turned black,” etc.)

Daily recording is a preventive maintenance program and when comparing values with engine history it will help
you recognize conditions, signs or indications of approaching trouble. Daily operation records also make trouble
shooting easier and will lessen the down time (to save time and money for servicing).

Plus d'informations sur : www.dbmoteurs.fr

«
...
37
38
39
40
41
...
»

Summary of Contents for D25A MS
























































































Reviews:

No comments

Related manuals for D25A MS

Brand: EBARA Pages: 36

Brand: RHINO MOTION CONTROLS Pages: 4

Brand: Polini Pages: 32

Brand: E-MAG Pages: 30

Brand: Kohler Pages: 4

Lombardini SILEO 1000

Brand: Kohler Pages: 168

Brand: Hatz Pages: 112

Brand: ZF Pages: 80

Brand: RHINO Pages: 9

Brand: Jets Munt Pages: 24

Brand: Habasit Pages: 28

Brand: O.S. engine Pages: 17

Brand: O.S. engine Pages: 20

EPA04 Series 40

Brand: Detroit Diesel Pages: 158

Brand: Baumuller Pages: 19

Brand: Baumuller Pages: 31

Brand: LONCIN Pages: 64

Brand: Farymann Diesel Pages: 137

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands