Volvo Penta D25A MS Operator'S Manual Download Page 18 | Manualshive

Page: 18 / 87

background image

18

Standard control system

Instrument panels

Instrumentation for the main control position and auxi-
liary control position.

1. Temperature gauge. Indicates the engine coolant

temperature.

2. Oil pressure gauge. Indicates the pressure of the

engine lubricant.

3. Voltmeter. Indicates the charge voltage from the

generator when the engine is running and the bat-
tery voltage when the engine is stopped.

4. Tachometer. Indicates the speed of the engine in

rpm.

5. Hour counter. Shows the total number of engine

running hours as a decimal number.

6. Press button for testing and acknowledging

alarms (see next page “Warning displays”).

7. Siren for acoustic alarm that sounds if one of the

warning lamps comes on.

8. Warning display (see section “Warning displays”,

pos 1–3).

9. Starting switch (see next page).

10. Press button for instrument illumination.

This chapter describes the standard Volvo Penta instruments that are available for your engine. Note that that
tachometer, oil gauge, temperature gauge, charge gauge, starting switch, etc., that are shown here as panel
mounted, in some cases may be mounted separately.

If the vessel is equipped with instruments not described here and you are not sure of their function, please get in
touch with the shipyard or the company that installed the installation aboard the vessel.

IMPORTANT!

Read the chapter “Starting” before starting your engine.

11. Oil pressure gauge. Indicates the oil pressure in

the reverse gear.

12. Charge air pressure gauge. Indicates the turbo-

charger boost pressure.

Plus d'informations sur : www.dbmoteurs.fr

«
...
16
17
18
19
20
...
»

Summary of Contents for D25A MS
























































































Reviews:

No comments

Related manuals for D25A MS

Brand: Eaton Pages: 12

2-10-4 TEXAS STEAM ENGINE

Brand: Premier Pages: 24

Brand: Westerbeke Pages: 64

MAX-15CV-R Series

Brand: O.S. engine Pages: 34

Brand: O.S. engine Pages: 34

Brand: O.S. engine Pages: 40

Brand: STEPCRAFT Pages: 24

Brand: Superrollo Pages: 68

Brand: DoorHan Pages: 16

Brand: Doosan Pages: 179

Brand: DUROMAX Pages: 32

Brand: Volvo Penta Pages: 53

Brand: Volvo Penta Pages: 76

Brand: Lombardini Pages: 57

Brand: Lombardini Pages: 94

Nanomotion SE Series

Brand: Johnson Electric Pages: 33

Brand: YS Pages: 2

INline GSI56 e5 Series

Brand: GEIGER Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands