Volvo Penta D25A MS Operator'S Manual Download Page 74

Page: 74 / 87

Standard Control System

Fuel specification

Fuel must comply with national and international standards at the least, e.g.:

Property

Use limit

Flash point ..............................................................

As stipulated by regulation

First distillation point ..............................................

170°C (338°F) or more

90% distillation point ..............................................

330 to 380°C (626 to 716°F)

Pour point ...............................................................

6°C (10.8°F) below ambient temperature

Cloud point .............................................................

Below ambient temperature

Carbon residue (10% residue oil) ...........................

0.4 weight % or lower

Cetan number ........................................................

45 or more

Cetan index (new) ..................................................

45 or more

Kinematic viscosity .................................................

2.0 mm²/S or more [30°C (86°F)]

...............................................................................

8.0 mm²/S or lower [50°C (122°F)]

...............................................................................

10.5 mm²/S or lower [40°C (104°F)]

...............................................................................

16.0 mm²/S or lower [30°C (86°F)]

Sulfur content .........................................................

0.2 weight % or lower

Water and sediment ...............................................

0.1 volume % or lower

Ash .........................................................................

0.03 weight % or lower

Copper plate corrosion (100°C)[212°F], 3h ............

No. 3 or lower

Specific gravity (15°C/4°C [59°F/39°F] ..................

0.83 to 0.87

Coking test .............................................................

Not carbonized 100% at 250°C (482°F)

Aromatics content ..................................................

38 weight % or lower

Particulate contaminant ..........................................

5.0 mg/liter or lower

Asphaltene .............................................................

0.1 weight % or lower

Note!

It is necessary to use a fuel that has a pour point suitable for ambient temperature during the operation of

the engine. Consult the supplier to select the right type.

JIS KK 2204. ........................ Type1, Type2, Type3

ASTM, D975 ................................... No.1-D, No.2-D

BS2869 ................................... Class-A1, Class-A2

DIN51601 ............................................. Diesel-Fuel

ISO8217 ............................................... DMX-Class

Plus d'informations sur : www.dbmoteurs.fr

Summary of Contents for D25A MS
























































































Search results

Summary of Contents for D25A MS

Reviews:

Related manuals for D25A MS

Brands by name

Popular brands

Volvo Penta D25A MS, Operator'S Manual

Search results

Summary of Contents for D25A MS

Reviews:

Related manuals for D25A MS

Brands by name

Popular brands