Volvo Penta D25A MS Operator'S Manual Download Page 45 | Manualshive

Page: 45 / 87

background image

45

Maintenance: Fuel System

Bleeding the fuel injection pump

1. Loosen the air vent cock on the fuel injection

pump about 1.5 turns.

2. Move the priming pump cap up and down to start

the flow of fuel through the system.

3. When the fuel coming out of the air vent cock

shows no visible bubbles, lock the priming pump
cap while holding it down. Then tighten the air
vent cock.

Be sure to lock the priming pump cap before tight-
ening the air vent plugs and cock. If this is not
done the cap does not return to the original posi-
tion due to the pressure in the priming pump.

4. Tighten the priming pump cap by hand until the

tightening force increases, normally this occurs
after turning it approximately 70 to 90 degrees.
Mark this position on the priming pump cap to
make item 5 work more easily.

5. Tighten the priming pump cap an additional 120

to150 degrees using a wrench.

6. Clean the engine from spoiled fuel to prevent fire

and pollution of the environment.

IMPORTANT! If the priming pump cap is tighte-

ned too much (more than 240 degrees in total),
the top of the priming pump can be damaged.

IMPORTANT! Looseness of the priming pump

cap in combination with engine vibration may
cause engine failure and damage to the installa-
tion.

Plus d'informations sur : www.dbmoteurs.fr

«
...
43
44
45
46
47
...
»

Summary of Contents for D25A MS
























































































Reviews:

No comments

Related manuals for D25A MS

Brand: Quectel Pages: 71

Brand: HunterDouglas Pages: 20

Brand: Schweigen Pages: 28

Brand: DR Pages: 20

Command PRO EFI PCV850

Brand: Kohler Pages: 10

Brand: Saito Pages: 8

Brand: Eurotronic Pages: 4

Brand: Jiecang Pages: 2

Brand: Danfoss Pages: 77

Brand: Parker Pages: 32

Brand: dunkermotoren Pages: 32

Brand: Bosch Pages: 20

Rexroth Hagglunds CA 10

Brand: Bosch Pages: 53

Brand: Bosch Pages: 60

Brand: Bosch Pages: 74

Rexroth Hagglunds CA 100

Brand: Bosch Pages: 76

Rexroth 70 Series

Brand: Bosch Pages: 56

Rexroth IndraDyn T

Brand: Bosch Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands