Vogt TUBE-ICE P-118F Service Manual Download

Page: 98 / 115

P118F Service Manual

OPTIONS AND ACCESSORIES

1/6/09

10-6

Delay On Make

Ranges from Off to 10 minutes in .1 minute increments. Use the arrow keys for adjustment. “Delay On Make” is

energized when the control voltage is reactivated, and the load will remain off until the specified time has elapsed.

Default is .1 minute.

Phase Unbalance

Use the arrow keys to set the Phase Unbalance percentage (2 to 20%) of incoming 3 Phases. This will turn off

equipment for a specified time if incoming Phase Unbalance exceeds set percentage. The recommended setting is 5%.

Default is 5%.

Delay On Fault

Ranges from Off to 15 seconds in .1 second increments. Use the arrow keys for adjustment. “Delay On Fault” is

energized when any line fault occurs. The fault must be present set time in order to be registered or acted upon. Default

is 2.0 seconds.

Contactor Test

Selectable number of Contactor Retries (1 to 10 or OFF) on Contactor Fault. Use the arrow keys to adjust the number of

times the contactor will be operated in order to seal the contacts. Setting retries to OFF means do not check load side.

Any input to the load inputs will be ignored. Default is off.

Reset Mode

(Manual/Automatic) Choose whether to let the unit automatically reset or to wait for you to manually reset it. The

recommended setting is automatic because faults must be cleared in order to reset from the manual mode. To reset from

a fault condition in the manual mode press and hold the fault button for two seconds. Default is manual reset.

Control Mode

This setting allows you to select the control source. Pressing the arrow keys in this setup mode takes you through ON,

OFF and EXTERNAL. The normal setting would be EXTERNAL. With the control set to EXTERNAL the unit will

respond to the signal connected to the CONTROL input. With the control mode set to ON the unit will turn on its

output relay if line parameters are within setup parameters. Setting the control mode to OFF causes the unit to ignore

the control input and keep it’s output relay off. Default is external.

Summary of Contents for TUBE-ICE P-118F




















































































































Search results

Summary of Contents for TUBE-ICE P-118F

Reviews:

Related manuals for TUBE-ICE P-118F

Brands by name

Popular brands

Vogt TUBE-ICE P-118F, Service Manual

Search results

Summary of Contents for TUBE-ICE P-118F

Reviews:

Related manuals for TUBE-ICE P-118F

Brands by name

Popular brands