manualshive.com logo in svg

Viking Designer EPIC, User Manual

Share
Download
Viking Designer EPIC User Manual Download Page 92

Tension too tight

If the bobbin thread is visible on the top side of the fabric,
the thread tension/thread portioning is too tight. Reduce the
thread tension/thread portioning.

Tension too loose

If the upper thread is visible on the back side of the fabric,
the thread tension/thread portioning is too loose. Increase
the thread tension/thread portioning.

For decorative stitches and buttonholes the upper thread
should be visible on the back side of the fabric.

Make a few tests on a scrap piece of the fabric you are going
to use and check the tension.

Mirroring

1. Mirror end to end

2. Mirror side to side

To mirror a stitch or stitch program lengthwise, touch the
mirror end to end button. To mirror a stitch or stitch
program sideways, touch the mirror side to side button.

Tip: Use the smart toolbox to open a shortcut for mirroring.

Note: Some stitches e.g. buttonholes cannot be mirrored.

92

7 Sewing

Summary of Contents for Designer EPIC







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands