Viessmann B1HA Installation And Service Instructions Manual Download Page 63

Page: 63 / 92

5784 568 - 13

Vitodens 100-W, B1HA/B1KA 26 to 125 Combi Installation/Service

Troubleshooting

Boiler Connection

(continued)

Check outdoor temperature sensor

1. Disconnect cables from outdoor sensor.

2. Measure resistance of the outdoor sensor and

compare with resistance / outdoor sensor curve

shown

below.

3. If the value measured differs significantly, replace

the

sensor.

In weather-compensated mode (optional), the boiler

water temperature is regulated subject to the outdoor

temperature.

Frost protection function

Built-in automatic frost protection allows the boiler to be

shut off for an extended period of time while protecting

it against freeze-up. Frost protection is continually active.

The burner is switched ON when the boiler water

temperature reaches 41ºF (5ºC) and is switched OFF

again when the boiler water temperature reaches at least

59ºF (15ºC) [but not more than 68ºF (20ºC)].

For details on the control, please refer to

the Vitodens 100-W Operating Instructions.

Resistance in K



Temperature

Summary of Contents for B1HA





























































































Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands

Viessmann B1HA, Installation And Service Instructions Manual

Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands