Viessmann B1HA Installation And Service Instructions Manual Download Page 25

Page: 25 / 92

5784 568 - 13

Vitodens 100-W, B1HA/B1KA 26 to 125 Combi Installation/Service

Waterside flow (primary circuit)

The Vitodens 100-W, B1HA/B1KA is designed for closed

loop, forced circulation hot water heating systems only.
Use standard friction loss method for pipe sizing. Observe

boiler maximum and minimum flow rate limitations.

If system flow rate exceeds boiler maximum flow rate

(as stated above), falls below the minimum flow rate

or if system flow rate is unknown, Viessmann strongly

recommends the installation of a low-loss header.

An alternative method may be used, such as primary

secondary piping using closely spaced tees. A low-loss

header offers additional benefits not provided by a pair

of closely spaced tees. Viessmann therefore strongly

recommends and prefers the use of a low-loss header

over closely spaced tees. Refer to the Technical Data

manual for low-loss header information.

Model B1HA 26, 94

1 boiler

Output (NG/LPG)

MBH



t for NG/LPG

20ºF (11ºC) rise GPM (L/h)

8.8 (1999)

25ºF (14ºC) rise GPM (L/h)

7.0 (1599)

30ºF (17ºC) rise GPM (L/h)

5.9 (1332)

35ºF (19.5ºC) rise GPM (L/h)

5.0 (1142)

40ºF (22ºC) rise GPM (L/h)

4.4 (999)

Boiler maximum flow rate 6.2 GPM (1400 L/h)

Pressure drop (primary circuit) for

Vitodens 100-W, B1HA 26, 35, 94, 125 and B1KA 35, 125

For sizing an on-site circulation system.

Max. flow rate: 6.2 GPM (1400 L/h)

Model B1HA 35, 125/B1KA 35, 125

1 boiler

Output (NG/LPG)

MBH

117



t for NG/LPG

20ºF (11ºC) rise GPM (L/h)

11.7 (2657)

25ºF (14ºC) rise GPM (L/h)

9.4 (2126)

30ºF (17ºC) rise GPM (L/h)

7.8 (1771)

35ºF (19.5ºC) rise GPM (L/h)

6.7 (1518)

40ºF (22ºC) rise GPM (L/h)

5.9 (1328)

Installation Examples

(continued)

Connections

Flow rate

Supply head pressure (water)

Summary of Contents for B1HA





























































































Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands

Viessmann B1HA, Installation And Service Instructions Manual

Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands