Viessmann B1HA Installation And Service Instructions Manual Download Page 39

Page: 39 / 92

5784 568 - 13

Vitodens 100-W, B1HA/B1KA 26 to 125 Combi Installation/Service

Accessing

Electrical Connections

(continued)

Control Connections

Legend

Tank temperature controller (field supplied)

Connecting a field supplied tank temperature controller on B1HA only (e.g. Honeywell Aquastat or others)

Legend

Tank temperature controller (field supplied)

Note:

see wiring diagram on page 76.

1. Cut off and discard the 2 red connectors labelled ‘5’.

See page 37 for location.

2. Strip

in. insulation from the 2 wires.

3. Connect the tank temperature controller wires using

wire

connectors.

Note:

To set up the boiler operation with the tank

temperature controller (refer to item 14 in the setup

menu on page 44).

Summary of Contents for B1HA





























































































Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands

Viessmann B1HA, Installation And Service Instructions Manual

Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands