Viessmann B1HA Installation And Service Instructions Manual Download Page 55

Page: 55 / 92

5784 568 - 13

Vitodens 100-W, B1HA/B1KA 26 to 125 Combi Installation/Service

Start-up, Inspection and Maintenance

Check Neutralization Unit (if applicable)

IMPORTANT

1. Check the pH value of the condensate with a pH

measuring strip. If the pH value is less than 6.5,

replace

granulate.

2. If contaminated: Rinse neutralization unit with tap water.
3. Add granulate as marked on the cartridge.

pH measuring strip is field supplied.

The granulate is consumed as it neutralizes the condensate.

The red marking indicates the min. filling level.

Installation Instructions Neutralization Unit

WARNING

Follow cleaning agent manufacturer’s safety

instructions and wear appropriate protective equipment.

Clean Combustion Chamber/Heat Exchanger Surfaces

WARNING

Never use a metal wire brush or mechanically driven

brushes.

1. Remove burner assembly and reinstall upon

completion of service work as per the instructions

on page 57 in this manual.

2. Clean the combustion chamber

by vacuuming

loose debris out.

3. Remove embedded sediment from the stainless steel

heat exchanger surface

by thoroughly rinsing with

water or solvent free cleaning agents such as citric

acid based cleaners. Consult a cleaning agent

manufacturer for a suitable product.

Avoid getting the refractory wet during cleaning.

Note:

Discoloration of the heat exchanger surface

is the normal result of the combustion process.

It has no impact on the functionality or the

longevity of the heat exchanger.

4. Use a non-metallic brush if necessary, with a gentle

brushing motion to remove the embedded

sediment.

It is not recommended to use chemicals to clean the

heat exchanger surface

5. If the gaps between the heat exchanger coil windings

are plugged, carefully remove debris without

scratching the heat exchanger surface using the

Viessmann tool specific for this purpose.

Tool part number 7840112;

Replacement blade part number 7840346.

6. Flush the combustion chamber

with water until it

runs clear through the condensate trap.

7. Remove and clean out any accumulated debris from

condensate trap. Reinstall condensate trap.

See page 54 for details.

Summary of Contents for B1HA





























































































Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands

Viessmann B1HA, Installation And Service Instructions Manual

Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands