Viessmann B1HA Installation And Service Instructions Manual Download Page 36

Page: 36 / 92

5784 568 - 13

Vitodens 100-W, B1HA/B1KA 26 to 125 Combi Installation/Service

Control Connections

Accessing

Electrical Connections

Rotating the control unit and opening the power/pump module

Press in the control retaining tabs.

With retaining tabs pressed in rotate the control

forward and down.

Release the 4 boiler cover retaining clips and pull

cover

off.

Terminal block for OpenTherm or room thermostat(s)

and outdoor temperature sensor.

Connectors for DHW tank temperature sensor or tank

temperature controller (e.g. Honeywell aquastat and

connections, see the following pages for details.

Note:

this terminal block may be removed for ease of

connection.

Removing the front cover

1. Loosen retaining screws, screws are captive and do

not need to be fully removed.

2. Remove the front panel.

Summary of Contents for B1HA





























































































Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands

Viessmann B1HA, Installation And Service Instructions Manual

Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands