Viessmann B1HA Installation And Service Instructions Manual Download Page 62

Page: 62 / 92

5784 568 - 13

Vitodens 100-W, B1HA/B1KA 26 to 125 Combi Installation/Service

Boiler Connection

Start-up and Maintenance

Remove front panel

Check boiler temperature sensor

1. Loosen retaining screws, screws are captive and do

not need to be fully removed.

2. Remove the front panel.

Resistance in K



Boiler water temperature

1. Disconnect cables from boiler temperature sensor

2. Measure resistance of the boiler temperature sensor

and compare with resistance/boiler water temperature

curve

shown.

3. If the value measured differs significantly, replace the

sensor.

WARNING

The boiler temperature sensor is immersed in the

heating water (risk of scalding).

Drain the boiler before replacing the sensor.

Troubleshooting

Summary of Contents for B1HA





























































































Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands

Viessmann B1HA, Installation And Service Instructions Manual

Search results

Summary of Contents for B1HA

Reviews:

Related manuals for B1HA

Brands by name

Popular brands